adc

ADC K8 Cartridge Specification
- Frequency Response: 15hz-20khz
- Channel Separation: 24 (dB at 1 kHz/10 jHz)
- Vertical tracking force (grams): 1.0-2.0
- Recommended load impedance (ohms): 47k
- Output: 5 mv

ADC K8 Cartridge Specification
- Frequency Response: 15hz-20khz
- Channel Separation: 24 (dB at 1 kHz/10 jHz)
- Vertical tracking force (grams): 1.0-2.0
- Recommended load impedance (ohms): 47k
- Output: 5 mv

The ADC LMA-1 LMA 1 LMA1 phono cartridge is sold out and no longer available.

The ADC LMA-3 LMA 3 LMA3 phono cartridge is discontinued and is no longer available.

The ADC LMH-I LMH I LMHI headshell for straight tonearms comes in a black with diagonal silver stripes factory box. Inside the box is the superbly crafted ADC headshelll with the gold-plated headshell wires installed. No other accessories are included.

For the made-in-Japan replacement ADC-type headshell, refer to the Related Products below.

The ADC QLM-32 MKIII QLM 32 MKIII QLM32 MKIII phono cartridge was one of the most popular cartridges. We were able to obtain new old stock units but sadly these are gone. We do not know when and if we will again be able to obtain new inventory.

ADC R-15E ORIGINAL STYLUS

The R-15E stylus is the specified stylus replacement for the ADC 10E Mark IV Cartridge. It feature a .3 x 0.7 mil. Elliptical stylus with a tracking force range of 0.5- 0.7 grams. The stylus can also be used to replace the following ADC Styli: R-26, R-27, R-251, R-252 & R-253.

ADC RK-8 RK 8 RK8 STYLUS

The ADC RK-8 RK8 stylus features a conical diamond for long playing life and good rendition of voice and music.

Upgrade Options
- For upgrades and accessories that enhance sound quality and fidelity, refer to Related Products near the bottom of the page.

ADC RK-8E RK8E STYLUS

The ADC RK-8E RK8E needle stylus for the ADC K-8E K8E phono cartridge features a highly polished elliptical diamond designed for more effective tracing of record grooves. It results in very high musical accuracy, better tonal balance and harmonically complete sound quality.

Upgrade Options
- For an upgrade stylus and accessories that enhance sound quality and fidelity, refer to Related Products section near the bottom of this page. As the prices go up on replacement needles, the tip types usally get finer, or an OEM stylus could be offered. Finer cut tips allow for better fidelity and reduced record wear.

The ADC RLMA-1 RLMA1 Accutrac stylus is used with the ADC LMA-1 LMA1 and LMA-3 LMA3 phono cartridges.

The ADC RLMA-3 RLMA3 Accutrac stylus is used with the ADC LMA-3 LMA3 and ADC LMA-1 LMA1 phono cartridges.

For a stylus replacement that offers improved sound quality and performance, refer to the Related Products.

The ADC RPSX-10 RPSX10 stylus features a highly polished special 0.65 bonded conical diamondfor long playing life, precision tracing of record grooves and accurate rendition of voice and music.

The ADC RPSX-30 RPSX30 stylus features a highly polished special elliptical diamond with a .0003 x .0007 inch tracing radii for long playing life, precision tracing of record grooves and accurate rendition of voice and music.

We apologize, but this item is currently unavailable and we're not sure if and when we will receive more.

The ADC RPSX-40 stylus features a highly polished special elliptical diamond with a .0003 x .0007 inch tracing radii for long playing life, precision tracing of record grooves and accurate rendition of voice and music. The ADC RPSX-40 stylus is used with the ADC PSX-40 cartridge and its series.

Genuine ADC RS IV stylus for Digital Series IV and to upgrade lower model Digital series cartridges. The ADC RS IV stylus features a highly polished .0002 x .0007 inch Nude Micro Ellipse diamond tip designed for highly precise tracing of record grooves. It results in excellent musical accuracy, improved tonal balance and higher sound quality. The stylus is made in USA by Audio Dynamics Corp (ADC).

ADC Series IV cartridge | ADC RS IV stylus Details
- Diamond tip: Nude Micro Ellipse
- Diamond tip dimensions: .0002 x .0007 inch
- Tracking force: 1.2 g +/- .02 g
- Frequency response: 15 Hz - 25 kHz +/- 2dB
- Output @ 5 cm/S: 4 mV
- Channel balance: 1 db maximum
- Channel separation @ 1k | 10kHz: 26 dB | 15 dB
- Inductance: 589 mH
- Resistance: 820 Ohms
- Load Resistance: 47 k Ohms
- Load capacitance: 275 pf
- Cartridge weight: 5.75 g